Best family tree software for mac. Search and Share Using FamilySearch. ICloud Integration. Global Search & Replace. Person Merge. Online Features & Collaborations.
• MAGICAR M870AS Car alarm with two-way remote and remote - start system Installation guide. • TABLE OF CONTENTS I. INTRODUCTION..4 II. PLACING..4 III. ADDITIONAL RELAY 12V CONNECTION.1 IV. WIRING ARRANGEMENT..6 V. CONNECTING OF CLUTCH SENSOR..1 VI.
REMOTE START LOOP..10 VII. Programming of optional functions..10 Programming menu No. 1..11 Programming menu No.2..12 VIII. CALIBRATION OF THE FUNCTION – HAZARD LIGHT MODE.13 IX. INTRODUCTION MAGICAR M870AS is a safety device with the highest level of security. Thanks to the 2-way remote with pager you will be immediately informed about possible car intrusion, as well as the manner of the intrusion even though you are too far from the car to hear the siren. When installing the alarm into a manual transmission car, you must not cut off the remote starting loop located in the alarm control unit.
Performance Teknique ICBM-7071; 2-Way FM Car Alarm Security w/ LCD Status Display w/Remote Engine Start; For Both Manual and Auto Transmission; Note:. Factory Alarm Disarm Output. The Magicar FAI-8100 is the unique Auto Security Remote Start System incorporated with Super FM Paging Circuit. So read this owner manual carefully before you operate the Magicar FAI-8100 system.
In case the remote starting loop is cut off, you must reconnect it or install the alarm into an automatic transmission car In case of an automatic transmission car, where an engine can be started without a gear stick in ‘N’. • +12V If you want to change the signal polarity (-) to (+) E.g.: When AUX is installed, a relevant device is operating on (+). Output (+) impuls (-) If you want to disconnect two wires by a (-) signal +12V E.g.: With a (-) signal, lines A and B are cut off.
• - Negative parking lights input (-). When switching on Magicar M870AS this will indicate the lights are on. 8 – orange - Positive parking lights input (+). When switching on Magicar M870AS this will indicate the lights are on. 9 – grey/black. • 10 – brown/black - Negative hood switch input (-) 11 –black/white - Foot brake input reacting on (+) 12 – light blue/black - Emergency Brake input reacting on (-) additional outputs CONNECTOR 5 - red Additional outputs controlled by the remote control. For switch settings see programming menu 2-08, 2-09, 2-10.
• UART CONNECTOR 6 - black CONNECTOR 7 - blue Antenna CONNECTION 8 - blue Temperature sensor CONNECTOR 9 - white LED indication CONNECTOR 10 - white RPS sensor CONNECTOR 11 - red Shock sensor 3 – red 1 – black - grounding - power supply of +12 V 4 –. REMOTE START LOOP The remote start loop is located under the cover of the main unit of the car alarm: loop Cut off: Automatic transmission Not cut off: manual transmission Attention! When the loop is cut off, you can start remotely at anytime. Therefore, the loop can only be disconnected in cars that can be started only in parking or neutral position. • Programming menu No.
1 When the door is open and ignition is on keep buttons I and II pressed simultaneously for 2 sec. Options Function Button I Button II Button III Button IV TURBO mode 2 min 1 min 1-01 1-02 Regular starting Engine running time.
• This function is available with CAN Bus module. In case you are using read only mode > Magicar will only read data from CAN (trunk, door, hood). In read/write mode > data will read and write to CAN (trunk, door, hood, lock and unlock, indicators, lock and unlock except closing windows.). • Programming menu RESET In case you wish to set all the function back to the pre-set, you can do so by the following way. All the functions will be set to option 1. Procedure: 1.
Turn the ignition on and open the door. Calibration is successfully completed. Turn the hazard light button off, turn the ignition off and release the brake pedal. Connect the light output wire (CN2-1) to the hazard light switch wire (Figure No.1). Check the polarity of common wire CN1-6. After this connection the alarm will control flashing of the lights. • Valet mode deactivation.